How to Dye Blackout Curtains: Fabric Test, Dye Choice, Steps

Woman dyeing blackout curtain fabric teal blue in a plastic tub at home using a DIY fabric coloring method.

Your blackout curtains may be faded by the sun, or the color may no longer match your room. New panels cost a lot, so fabric dye looks like an easy fix. But these curtains have a foam backing that blocks light, and dye can’t change it. Below, you’ll learn how to dye blackout curtains while keeping risks low. You will check your care label, pick the right dye, like Rit DyeMore or Rit All-Purpose, and test a scrap first. That way, you can change the color and protect the blackout effect.

Can You Dye Blackout Curtains?

Sometimes. Cotton, linen, and poly-cotton blackout curtains can be dyed with fabric dye. Most blackout curtains are polyester with a foam backing, so they need a synthetic dye like Rit DyeMore. Dye colors only the front fabric, not the backing. Test a hidden scrap first. Dark curtains can’t be dyed lighter.

  • Works: Cotton, linen, and cotton-rich blackout curtains. These natural fibers soak up Rit All-Purpose dye easily, and the color comes out even.
  • Risky: Polyester curtains with a foam or acrylic backing and poly-cotton blends with more than 35% polyester. Rit DyeMore can color the front fabric, but the hot dye bath might harm the backing. Always test a scrap from the hem first.
  • Won’t work: Fire-retardant (FR) curtains, heavily coated curtains, and “dry clean only” curtains. Their special finish blocks the dye. Dark curtains also can’t turn lighter, because dye adds color and never removes it.

How Blackout Curtains Are Made (And Why It Affects Dyeing)

Blackout curtains are made by coating the back of a polyester fabric with layers of foam. Black foam stops the light, and white foam covers it. Dye colors only the front fabric, so the foam never changes color.

Foam Coating: 2-Pass vs. 3-Pass Blackout

Think of a sandwich: the curtain fabric is the bread, and each foam layer is a “pass.”

A 2-pass blackout has black foam first, then a white foam layer on top. The black foam can show through the front fabric, so the dyed color may look darker than the bottle promises.

A 3-pass blackout has white foam, black foam, then white foam again. The extra white layer hides the black foam, so the dyed color looks truer.

To check, hold a corner up to a phone flashlight. A gray shadow suggests 2 passes.

Face Fabric vs. Coating: What Dye Can and Can’t Change

The face fabric is the cloth you see. The coating is the acrylic foam on the back.

Dye soaks into face fabric threads. Cotton and linen take it easily. Polyester needs Rit-Dye. More in a hot stove-top dye bath.

Dye can’t change the coating. It’s plastic-like, so the black foam stays black, and your curtain should still block light.

The risk is heat: a bath near 180°F to 220°F might soften the coating, though this isn’t well tested. Cut a hidden hem scrap and dye it first.

Fire-retardant (FR) finishes can also block dye. Check your care label for the fiber type and any “dry clean only” warning.

How to Check Your Curtain Fabric Before Dyeing

Person performing a curtain fabric check by reading the care label on gray blackout curtains before dyeing.

Check the care label first. It tells you the fiber, like cotton or polyester. If the curtain has more than 35% synthetic fiber, use Rit DyeMore. Also look for fire-retardant or dry-clean-only tags, then test a hidden scrap before dyeing everything.

Read the Care Label (35% Synthetic Rule).

Flip your curtain over and find the small care label near a bottom corner. It lists the fiber content, such as cotton, linen, or polyester. Here is the 35% synthetic rule. If the label shows more than 35% polyester, acrylic, or nylon, you need Rit DyeMore. If it shows less, Rit All-Purpose works. Rit All-Purpose can’t color polyester at all. No label? Treat the curtain as polyester, since most blackout curtains are.

Fire-Retardant (FR) and “Dry Clean Only” Curtains

Fire-retardant (FR) curtains have a special chemical finish that often blocks dye. Look for words like “FR,” “flame retardant,” or “NFPA 701” (a U.S. fire safety standard) on the label. “Dry clean only” curtains may also resist dye or shrink in water. If you see either tag, expect a patchy color. Fabric paint or new curtains may be a safer choice.

Do a Scrap or Hem Test

Cut a small square from a hidden hem or the bottom corner. Dye it with the same dye, heat, and time you plan to use. Rinse and dry it. Now check three things: the final color, whether the dye took evenly, and whether the foam backing stayed smooth. If the backing cracks or peels, stop. Heat may stress the coating, so this protects your curtain.

Best Dye for Blackout Curtains

Rit DyeMore is the best dye for polyester blackout curtains, while Rit All-Purpose works best on cotton and linen. Check the care label first. Fabrics with over 35% synthetic fiber need DyeMore, and both dyes give the best color on light-colored curtains.

Rit Dye More (Polyester and Synthetics)

Rit DyeMore is a liquid dye made for polyester, acrylic, nylon, and acetate. It also works on poly-cotton blends. Most blackout curtains use polyester, so this is your main choice. One bottle colors about two pounds of dry fabric. For 100% polyester or deep colors, double the dye. It needs a hot stovetop dye bath, and the fabric should soak for at least 30 minutes. Always test a scrap first.

Rit All-Purpose (Cotton, Linen)

Rit All-Purpose dye suits cotton, linen, and rayon curtains. It is easy to find at stores like Walmart and Michaels. It won’t color polyester or polyester thread, so stitching may stay light. Use it only if your care label shows less than 35% synthetic fiber. Natural fibers soak up this dye evenly.

Other Options (Tulip, Jacquard)

Tulip and Jacquard also make dyes you can use for dyeing blackout curtains. Tulip sells hot-dye powder and washing machine dye pods. Jacquard offers dyes for different fibers. Some of these are not made for polyester, so read the label first. If your curtains are synthetic, Rit DyeMore is the safer pick.

Fabric typeBest dyeMethodDifficulty
Cotton or linenRit All-PurposeStove top, bucket, or washing machineEasy
Poly-cotton (over 35% polyester)Rit DyeMoreStove topMedium
100% polyesterRit DyeMore (double dose)Stove topHard
FR or heavily coatedFabric paintPaint or sprayHard

What You’ll Need

You need curtain fabric dye, a large stainless steel pot, rubber gloves, and a kitchen scale. Dye and small supplies usually cost about $15 to $30. Keep the pot for dyeing only, never for food.

ItemWhy you need itPrice (USD)
Rit DyeMore or All-PurposeColors the fabric$5-$8 per bottle
Large stainless steel potHolds dye bath freely$20-$35
Rubber glovesProtect hands from dye stains$3-$5
Kitchen scaleWeighs curtains for dye amount$10-$15
Dish soapHelps dye spread evenlyAbout $3
Long spoon or tongsStirs fabric during soaking$3-$6
Plastic sheet or old towelsProtect floors and counters$2-$5

How to Dye Blackout Curtains Step by Step

Step-by-step guide to dye blackout curtains, showing fabric weighing, prewashing, dye mixing, soaking, rinsing, and drying teal curtains.

To dye blackout curtains, weigh the curtains, prewash them, and mix Rit Dye. More in a hot stovetop bath, soak for 30 minutes or more, then rinse and dry. Test a hidden scrap first, because heat may harm the foam backing.

Steps 1-6: Weigh, Prewash, Mix Dye, Dye Bath, Rinse, Dry

Step 1: Weigh the curtains. Put the dry curtain panels on a kitchen scale. One bottle of Rit Dye More colors about two pounds of dry fabric. For 100% polyester or deep colors, double the dye.

Step 2: Prewash and keep them damp. Launder panels in gentle detergent so dirt and factory finishes wash away.
Leave them wet, because damp fabric takes dye more evenly than dry fabric. Don’t use fabric softener.

Step 3: Mix the dye bath. Fill a large stainless steel pot with water until the curtain can move freely. Heat it to a simmer, about 180°F to 220°F. Add shaken Rit Dye. Mix in one teaspoon of dish soap.

Step 4: Soak for 30 minutes or more. Lower the damp curtain into the dye bath and stir often with tongs. Polyester needs at least 30 minutes, sometimes an hour. Keep checking the backing and stop if it looks warped.

Step 5: Rinse repeatedly until no color bleeds. Rinse the curtain in warm water first, then cooler water. This washes out loose dye so it won’t rub off on your walls, windows, or furniture.

Step 6: Wash and dry. Launder each panel separately in cool water using gentle detergent. Then air-dry it, or use the lowest dryer heat. High heat can stress both the new dye and the foam coating.

How to Get an Even Color on Large Panels

Dye one panel at a time, using the same dye amount and soak time for each. Use the biggest pot you own, because crowded fabric turns blotchy. Stir often and lift the curtain now and then so the dye bath reaches every fold. Weigh each panel first, so both end up the same shade. Mix a fresh dye bath for the second panel so the color matches.

Easier Alternatives If Heat Isn’t Safe

If heat could harm the foam backing, try washing machine dye on cotton or linen, or use fabric paint with fabric medium. Spray fabric paint works for quick touch-ups. Avoid plain acrylic paint, because it dries stiff and cracks.

Washing Machine Dye

Washing machine dye is the easiest choice for cotton and linen blackout curtains. Tulip dye pods and Rit All-Purpose both come with washer directions. Load the dye and damp curtain together, then read the label. Skip this method for polyester, because synthetic fibers need a hot stovetop bath. Afterward, run an empty wash cycle to clear leftover dye.

Fabric Paint With Fabric Medium or Spray Fabric Paint

Try fabric paint instead if the dye refuses to hold. Mix latex paint with fabric medium, a craft-store additive that keeps the cloth soft. Spray fabric paint, sold at Michaels, covers curtains quickly with no mixing. Paint sits on top of the threads, so you may need to coat both sides. Use it for stencils, stripes, or small areas, not a full recolor. Sample it on a concealed hem first.

Why Plain Acrylic Paint Stiffens the Fabric

Plain acrylic paint dries into a hard, plastic-like layer. When the curtain bends, the paint cracks and flakes off. The fabric also feels stiff, like cardboard. Fabric medium thins the paint and keeps it flexible. If you paint your blackout curtains, always add fabric medium and brush on thin coats.

Common Problems and Fixes

Most dyeing problems come from too little water, too little dye, or too little stirring. Blotchy color, light thread, stiff fabric, and rubbing dye each have a simple fix. Light leaking means the foam backing may be damaged.

Blotchy color means the pot was too small or the curtain started to dry. Redye in a bigger stainless steel pot with damp fabric and keep stirring.

Sewing thread stays light because Rit All-Purpose can’t color polyester thread. Use Rit DyeMore, or pick a darker dye shade that hides the contrast stitching.

Stiff fabric often means paint or heat. Plain acrylic paint dries hard, so add fabric medium. After dyeing, skip high dryer heat and rinse well to remove extra dye.

Color rubbing off happens when extra dye stays in the fabric. Rinse until the water runs clear, then wash the curtain alone in cold water for its first few washes.

Light leaking means the foam backing may have cracked in the hot dye bath. Hold the curtain to a window. If light shows, add a blackout liner or replace it.

How to Care for Dyed Blackout Curtains

Wash dyed blackout curtains alone in cold water for the first few washes. Use mild detergent, air-dry them, and avoid high dryer heat. Keep them out of strong, direct sun, because fresh dye can fade.

Keep dyed panels apart from other laundry and use cold water initially. Extra dye can bleed onto other laundry. Our tutorial on washing blackout curtains at home explains every gentle step.

Skip high heat in the dryer, since it can stress the dye and the foam backing. Read whether you can put blackout curtains in the dryer before you try.

New dye can still fade in strong sunlight. A sheer curtain in front can soften the UV rays. See do blackout curtains fade over time for more ways to slow fading.

Should You Dye or Buy New Blackout Curtains?

Dye your blackout curtains if they are cotton, linen, or light-colored and you want a small color change. Buy new ones if they are 100% polyester, fire-retardant, or if you want a much lighter shade.

FactorDye kitNew panels
CostLow, about $15-$30 for dye and suppliesHigher, full price per panel
TimeA few hoursShipping wait of days
RiskBlotchy color, backing damageLow risk
Color changeDarker shades onlyAny color
Best forCotton, linen, light curtainsFR or 100% polyester curtains

If your curtains pass the scrap test, dyeing can save money and give you a fresh color. If the foam backing cracks or the dye won’t stick, new panels are less stressful. Browse our picks for polyester blackout curtains when it’s time to replace them.

Conclusion

Now you know how to dye blackout curtains the safe way. Check your care label first, because cotton and linen take Rit All-Purpose easily, while polyester needs Rit Dye. More in a hot stovetop bath. Always test a scrap from the hem, since dye colors only the face fabric and heat may harm the foam backing. If your curtains are fire-retardant or you want a lighter shade, new panels are the smarter choice.

FAQs

1. Can you dye 100% polyester blackout curtains?

Yes, but it is hard. Use Rit Dye. More on a hot stove top. Double the dye and soak for at least 30 minutes. Test a hidden scrap first, because heat may harm the foam backing.

2. Will dyeing reduce the blackout effect?

Usually not. Dye colors only the face fabric, so the foam coating still blocks light. Heat or rough handling could crack the backing. Hold the curtain up to a window after dyeing to check for light leaks.

3. Can you dye black blackout curtains lighter?

No. Dye adds color and can’t remove it. Rit Color Remover also fails on polyester. A black curtain can stay black or go darker, but it can’t turn lighter.

4. Can I use Rit All-Purpose dye on blackout curtains?

Only on natural fibers. Rit All-Purpose works on cotton and linen, or fabric with under 35% synthetic fiber. It won’t color polyester, so use Rit DyeMore instead.

5. Can you use fabric paint on blackout curtains?

Yes. Mix paint with fabric medium or use spray fabric paint. It works best for stencils, stripes, and small areas. Plain acrylic paint dries stiff and cracks, so skip it.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top